![]() Locate screws for step 3C and keep them within reach What is the diameter of the hole in the door? IMPORTANT : Make sure the latch bolt is fully retracted (in the unlocked position).Hold the latch in front of the door hole, with the latch face flush against the door edge.Note : Please contact customer service if door thickness exceeds 1-3/4 in Measure to confirm that the door is between 1-3/8 and 1-3/4 in (35 mm and 44 mm) thick. Measure to confirm that the hole in the door edge is 1 in (25 mm). Measure to confirm that the backset is either 2-3/8 or 2-3/4 in (60 or 70 mm). Consult the deadbolt drilling instructions at Note : Additional door preparation may be required for doors with 1-1/2 Measure to confirm that the hole in the door is either 2-1/8 in (54 mm) or 1-1/2 in (38 mm). ![]() If drilling a new door, use the supplied template and the complete door Prepare the door and check the dimensions Follow the instructions in the user manual to program the lock with a new user code and to test the lock.Īdditional Tools (depending on the application).Make sure the flat blade is centered in the mounting plate hole. Tighten screws evenly, but do not over-tighten screws. The top of the mounting plate should be visible and kept parallel to edge of door. Support exterior assembly during mounting plate installation and make sure bolt is retracted. Rotate the flat blade to a horizontal position to match the latch orientation. Install exterior keypad and mounting plate.Locate screws for step 3C and keep them within reach.If it is 1-1/2 in (38 mm), an adapter ring is required. If it is 2-1/8 in (54 mm), an adapter ring is not needed for installation. Confirm the diameter of the hole in the door.Make sure the latch bolt is fully retracted (in the unlocked position). Install latch in the door with wood block and hammer. Align tabs with holes in collar and ensure collar snaps into place. Make sure the hole in the door frame is drilled at least 1 in (25 mm) deep and that the slotted hole is at the bottom of the latch. Install the latch in the door with supplied screws.If not, remove the latch face with a flathead screwdriver, twist collar off, and install drive-in collar. If the door edge is chiseled, install the strike on the door frame.If not, rotate the latch face as shown to extend the latch. Hold the latch in front of the door hole and confirm that the rectangular-shaped hole is centered in the door hole.If the door thickness exceeds 1-3/4 in, contact customer service for a thick door kit. Confirm that the door edge is 1 in (25 mm) and between 1-3/8 and 1-3/4 in (35 mm and 44 mm) thick.Additional door preparation may be required for doors with 1-1/2 in (38 mm) holes.Confirm that the door is either 2-1/8 in (54 mm) or 1-1/2 in (38 mm) thick with a backset of either 2-3/8 or 2-3/4 in (60 or 70 mm).If drilling a new door, use the supplied template and complete door drilling instructions available at.Screwdrivers, and additional tools such as a hammer, wood block, adapter ring, ![]() The product comes with required tools, including batteries, a ruler, Mm) thick and have a backset of either 2-3/8 or 2-3/4 in (60 or 70 mm). ![]() It is compatible with doors that are either 2-1/8 in (54 mm) or 1-1/2 in (38 The deadbolt requires batteries and can be unlocked using the keypad or a key. Package includes a latch, interior assembly, exterior assembly, transitional, The product is a Kwikset SmartCode 913 Electronic Deadbolt with a keypad. Kwikset Powerbolt 250 Keypad Electronic Lock Install the batteries in the interior assembly.Kwikset Powerbolt 250 Keypad Electronic Lock.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |